HTPHow to PackageProduction answers by Lancing UK
Liquid filling

How do I reduce drips, giveaway and waste when filling solvent-based products?

Practical guidance for solvent-based products: reduce product loss, damaged packs, film waste and avoidable rejects.

Answer format: direct explanation, ordered checks and relevant solution routes. . Application-specific engineering review is still required.

Direct answer

For solvent-based products, measure where material or product is lost and calculate waste per good pack. The result depends on product behaviour, supply conditions, dosing principle, nozzle design and container control. Start by separate product, packaging and rework waste and record measured fill weight or volume, cycle time and finished-pack leakage. Make one controlled change at a time so the original cause is not hidden by several new settings.

Production environment relevant to liquid filling
Higher-risk application: Use competent engineering, product-safety and compliance support. Product data, site classification, ventilation, containment, hygiene and validation requirements may change the correct solution.

What usually causes this?

  • overfilling, over-application or excessive trim used as a safety margin
  • A change in product temperature and viscosity or product supply pressure or level.
  • start-up and changeover settings not standardised
  • The equipment or handling method not being set for fast-evaporating formulations that can attack seals, hoses, liners and labels.
  • damaged or misfed packaging creating repeated rejects

Checks to make in order

  1. Separate product, packaging and rework waste
  2. Record measured fill weight or volume, cycle time and finished-pack leakage using a representative sample.
  3. Weigh or count loss during start-up, running and changeover
  4. Check dosing chamber, pump or valve condition, nozzle position and shut-off and container location beneath the fill point.
  5. Record the reason for every reject in a sample period
  6. Check whether waste changes with speed or pack size
  7. Calculate the financial value of giveaway and damaged packs

How to decide the next step

Solvent-based products involves fast-evaporating formulations that can attack seals, hoses, liners and labels. Prioritise the largest measured loss, then verify that the change does not reduce seal, dose or closure quality.

If adjustment and maintenance cannot hold the required result across the complete product and pack range, compare the machinery route against a written acceptance test. The important comparison is sustained good output—not only maximum cycle speed.

What to include in your production brief

Supplying the information below makes it much easier to distinguish a setup problem from a machinery or packaging limitation:

  • Product formulation or safety data
  • Normal filling temperature
  • Minimum and maximum dose
  • Acceptable fill tolerance
  • Container and neck dimensions
  • Required good packs per hour
  • Samples that represent solvent-based products
  • A short video of the current process and fault

Relevant solution websites

These specialist sites match the production process discussed above. Final suitability should be confirmed with samples, output, site and acceptance information.

Liquid FillersAutomatic Filling MachinesFilling Machines UK

Related questions

Production process relevant to how do i change a filler between pack sizes for solvent-based products?Liquid filling

How do I change a filler between pack sizes for solvent-based products?

Practical guidance for solvent-based products: make product and pack changes repeatable, measurable and easier for operators.

Read the answer →
Production process relevant to why do nozzles or valves block when filling solvent-based products?Liquid filling

Why do nozzles or valves block when filling solvent-based products?

Practical guidance for solvent-based products: trace the first loss of control instead of repeatedly clearing the final jam.

Read the answer →
Production process relevant to which wetted materials and seals are suitable for solvent-based products?Liquid filling

Which wetted materials and seals are suitable for solvent-based products?

Practical guidance for solvent-based products: check materials, seals, adhesives, films, closures and product-contact parts.

Read the answer →
Production process relevant to how do i reduce drips, giveaway and waste when filling thin free-flowing liquids?Liquid filling

How do I reduce drips, giveaway and waste when filling thin free-flowing liquids?

Practical guidance for thin free-flowing liquids: reduce product loss, damaged packs, film waste and avoidable rejects.

Read the answer →
Production process relevant to how do i reduce drips, giveaway and waste when filling foamy liquids?Liquid filling

How do I reduce drips, giveaway and waste when filling foamy liquids?

Practical guidance for foamy liquids: reduce product loss, damaged packs, film waste and avoidable rejects.

Read the answer →
Production process relevant to how do i reduce drips, giveaway and waste when filling viscous liquids?Liquid filling

How do I reduce drips, giveaway and waste when filling viscous liquids?

Practical guidance for viscous liquids: reduce product loss, damaged packs, film waste and avoidable rejects.

Read the answer →
Common search questions

Questions customers also ask

Open a question for a concise answer, then use the detailed guide above for the full production checks.

What should I check first for solvent-based products?

Separate product, packaging and rework waste

What commonly causes this problem with solvent-based products?

Common causes include overfilling, over-application or excessive trim used as a safety margin; A change in product temperature and viscosity or product supply pressure or level.; start-up and changeover settings not standardised.

How can I prove that an adjustment has worked for solvent-based products?

Record a representative baseline, change one variable at a time and repeat the same measurement over enough packs to show that the result is stable rather than a one-off improvement.

When should I consider a different machine or production method for solvent-based products?

Consider a different route when correct setup and maintenance cannot hold the required quality and sustained output across the complete product and pack range.

What information should I send before asking for a solution for solvent-based products?

Include Product formulation or safety data; Normal filling temperature; Minimum and maximum dose; Acceptable fill tolerance.

Which solution website is most relevant to this question?

The clearest starting point on this page is Liquid Fillers. Final suitability still needs to be confirmed using the actual product, packaging, output and site information.